 |
 |
 |
 |
 |
Test Method: D943 (Aluminum Block Bath) |
| Oxidation Stability Of Distillate Oil |
 |
 |
 |
 |
 |
 |
 |
 |
 |
• Meets the requirements of ASTM D943, D2274, D2893, D4310 test methods
• Digital indicating temperature control maintains ±0.1°C stability
• Aluminum Block bath with 4, 8 or 12 test positions
• Overall dimension 22”x 18”x 23” (55x 45x 58 cm), shipping weight 150 lbs
• Temperature range of 40 to 240'C
• Supplied with flow meter for each test position
• Available for either 115V, 208V or 220V, 50 or 60 Hz power |
 |
 |
 |
 |
Click for Liquid Baths
Click for Heated Tube Baths |
 |
 |
 |
 |
 |
 |
|
|
|
|
|
|
|
|
|
The series 30 Oxidation Baths meets the requirements of ASTM D943, D2893*, D4310, D6158, AOCS12-57* test methods (* modified version for these methods is available).
Each test position has one float-in-tube flowmeter positioned in front. The oxygen flow rate is maintained at 3 ± 0.1 L/hr with a micro precision valve.
Temperature control is provided by a digital display PID controller providing stability of ± 0.2º C or better. In the event of primary controller failure the bath is protected by a secondary high limit controller. Useful temperature range is from 40 to 240'C .
Water flow to each condenser is controlled by a valve mounted on the back panel. This is available only if the condenser water flows directly to a waste drain. If a recirculating chiller is to be used, only one flow valve is provided for each group of 12 condensers which must be arranged in series.
|
30-4
|
Four position, aluminum block bath with 4 flow meters (3L/h oxygen)
|
|
30-8
|
Eight position, aluminum block bath with 8 flow meters (3L/h oxygen)
|
|
30-12
|
Twelve position, aluminum block bath with 12 flow meters (3L/h oxygen)
|
|
| Accessories for each test position - ASTM D943, D4310 |
|
OX-18
|
Oxygen Delivery Tube |
|
OX-19
|
Oxidation Test Tube |
|
OX-20
|
Mushroom Condenser |
|
OX-21
|
Thermometer Bracket |
|
OX-23
|
Syringe Sampling Tube Holder |
|
OX-24
|
Stopper |
|
OX-28
|
Syringe Sampling Spacer |
|
OX-10
|
10 mL Syringe (a total of two only) |
|
OX-50
|
50 mL Syringe (a total of two only) |
|
OX-60
|
Syringe Sampling Tube |
|
OX-81
|
Wound copper and steel coil in a sealed tube, ready to use |
|
OX-85
|
Abrasive cloth, 100 grit silicon carbide |
|
|
|
|
Accessories for each test position - ASTM D2274
|
|
OX-18
|
Oxygen Delivery Tube |
|
OX-19
|
Oxidation Test Tube |
|
OX-20
|
Mushroom Condenser |
|
|
|
|
Suggested Additional Accessories:
|
|
OX-86
|
Oxidation test tube support rack for 12 tubes |
|
OX-87
|
Ventilated, darkened oxidation tube cooling rack, (12 tubes) for D2274 |
|
OX-88
|
Rubber tubing for condenser water, 12 ft (1.5 m) |
|
OX-89
|
Tubing for oxygen delivery, 50 ft (12 m) |
|
OX-91
|
Stainless steel funnel/filter holder with grounding cables & flask per Fig. 2 D2274 |
|
OX-92
|
Filter for D2274, pack of 50 matched-weight pair |
|
OX-100
|
Mass flow controller with touch panel interface software, each |
|
16
|
Refrigerated water chiller for up to 24 condensers |
|
65
|
Refrigerated water chiller for up to 60 condensers |
|
DAX
|
Paperless Videographic Recorder with flash memory card storage and ethernet |
|
|
|
Glassware and Other Components |
|
|
Oxidation Delivery Tube
|
|
Oxidation Test Tube
|
|
Condenser
|
|
Theomometer bracket
|
|
Stopper
|
|
Syringe Sample Tube Holder
|
|
Syringe Sample Spacer
|
|
Syringe Sample Tube
|
|
"O" Rings
|
|
|
Catalyst Coil
|
|
Wire Cooling Mandrel
|
|
Steel Wire
|
|
Copper Wire
|
|
Silicone Carbide Paper
|
|
Flexible Tubing
|
|
|
|
|
|
|
 |
|
